How To Fix Epson Error Code C1100 And Error 511
Over the past few days, some users have reported to us that they have experienced the Epson c1100 e 511 error code.
Don’t suffer from Windows errors anymore.
1. Download and install ASR Pro
2. Launch the application and click on the "Restore" button
3. Select the files or folders you want to restore and click on the "Restore" button
Download this fixer software and fix your PC today.
I would say remove the photoconductor unit. Check and reinstall the photoconductor and transfer ribbon. Clean the TR0 sensor in the printer’s instruction manual. Clean up any spilled toner inside the printer.
Description: Error TR0
– The PWBA microcontroller cannot receive a warning signal from SENSOR TR-0 (Sensor TR0) at the specified time.
Causes: • Photoconductor Assembly • TR-0 SENSOR • XERO CABLE ASSEMBLY • P/R MOTOR ASSEMBLY • MAIN CABLE ASSEMBLY • PWBA MCU • LV/HVPS
Solution: 1 Check the attachment of the photoconductor unit. Connect the photoconductor unit. Does the error continue to appear when you turn on the device? Continue to step 2]. End of Lesson 2 Testing the operation of the photoconductor unit Is the drum of the photoconductor unit rotating? Go to stepYu . Go to step .3 Check that the silver belt seal inside the photoconductor unit is free of dirt. Remove the photoconductor unit. Rotate the photoconductor gear up until the silver sealing strip is clearly visible. Money sealed? Replace the photoconductor unit. Go to step . 4 Checking the attachment of the TR-0 SENSOR (TR0 sensor) Remove the photoconductor unit. Is the SENSOR TR-0 securely attached? Go to step . Install the TR-0 SENSOR again, proceed to step .5 Check the surface of the TR-0 SENSOR for dirt and mysterious bodies. Remove the photoconductor unit. Is there a lot of dirt or foreign objects on the entire surface of TR-0 SENSOR? Clean to remove dirt or foreign matter to proceed to step . Go to step . 6 Does the error reoccur when you turn on the power? Go to step . Finishing the job Step 7 Check the relevant TR-0 SENSOR Remove the photoconductor unit. Voltage from P416-2. The P416-3 on the PWBA microcontroller has 5V DC in case silver paper or other reflective dots get close to the detection areas.SENSOR. And tr-0 is 5VDC when the object is discharged? Replace the PWBA microcontroller. Go to step . 8 5VDC sensor test on TR-0 Voltage P416-1 . P416-3 on your PWBA microcontroller is 5VDC? Go to step . Go to step . 9 CHECK FOR CONTINUITY OF THE XERO HARNESS ASSEMBLY Disconnect the MCU from the p/j416 PWBA. Do all of the following cables have normal continuity? J416-1. J108-3 J416-2 . J108-2 J416-3 . Replace SENSOR J108-1 TR-0. Replace XERO HARNESS. 10 Inspection after replacing the ENGINE P/R assembly. Replace ENGINE P/R assembly. Does the error repeat when you turn it on? Go to step . End of Exercise 11 Perform a 24 VDC power test for the MOTOR ASSY P/R. Disconnect P/J201 from MOTOR ASSY P/R. Is the voltage of .J201-1 .. J201-2 29 V DC? Go to step . Go to step . 12 Continuity Aspect HARNESS ASSEMBLY Disconnect all P/J403 connectors from the PWBA MCU. Is each of our continuities between all terminals on J403 normal? J200? Replace the PWBA microcontroller. Repair broken or shorted part. 16 MAIN HARNESS CHECK CIRCUIT ASSEMBLY DisconnectedInit P/J502 LV/HVPS from. Do all of the cables below have more or less continuity? j502-9. J201-1 J502-10 . Replace J201-2 LV/HVPS. Repair partial crack or short circuit. 14 VDC 8 PWBA MCU Power Check Voltage P410-3 . P410-4 on MCU PWBA is VDC? replace ten PWBA microcontrollers. Go to step . 15 MAIN HARNESS ASSEMBLY Inspection Disconnect P/J410 from PWBA MCU P/ and J502 from LV/HVPS. Do all cables in the following paragraphs have normal continuity? J410-3. J502-3 J410-4 . Replace J502-4 LV/HVPS. Repair the defective or shorted part.